Solvent Cement
The Solvent cement is
used for jointing PVC pipes & Fittings. Proper care
is always taken to ensure stringent quality checks on
the product at all stages, without compromising on the
quality. This is simple process for jointing RIGID PVC
PIPES with moulded or fabricated Fittings. The tools
required are a hacksaw with fine teeth, sandpaper,
cotton waste, a soft brush, a knife and solvent cement.
The jointing procedure is as under:
- Inspect the pipe and fittings to ensure that they match perfectly
- Cut the pipe square, using the hacksaw, clear burrs with knife and cotton waste
- Rub with the Sandpaper outside of pipe and inside of fittings. Clean again with cotton waste
- Apply solvent cement evenly with a soft brush on the outside of the pipe, to a width slightly more than
the corresponding depth, as also on the inside of the fitting
- Insert the pipe in fitting and turn it through 90ºC, to ensure uniform distribution of cement
- Hold the joint for 2 minutes and ensure that the pipe does not slip out of fitting
- Wipe out the excess cement from entire surface of the joint
- The joint should be allowed to set, undisturbed. It should be pressure tested only after 24 hours.
Applications
- It well be useful for jointing of PVC pipes and fittings
- It can be used for jointing any of two of the products made from PVC material
Available sizes
25 lm, 50 ml, 100 ml, 250 ml, 500 ml, 1000 ml, 5000 ml
Sizes of Solvenet Box Packing Will be as under
| 25 ml - 576 nos 50 ml - 288 nos 100 ml - 144 nos |
250 ml - 48 nos 500 ml -12 nos 1000 ml - 6 nos |
500 ml - 4 nos |
Safety Precautions
- Avoid contact with skin
- Always replace lids tightly after use
- Store in a cool place away from direct sunlight
- Do not breathe Solvent Cement vapours
- Shake the solvent cement container thoroughly before use
- Do not smoke while working with solvent cement, as it is highly inflammable
- The excess solvent should b e wiped out from entire surface of the joint
| Pipe
Dia
|
Approx. no. of
Joints / ltrs
|
Pipe
Dia
|
Approx. no. of
Joints / ltrs |
| 20 |
330 |
140 |
36 |
| 25 |
280 |
160 |
27 |
| 32 |
245 |
180 |
25 |
| 40 |
190 |
200 |
15 |
| 50 |
140 |
225 |
12 |
| 63 |
125 |
250 |
9 |
| 75 |
105 |
280 |
7 |
| 90 |
80 |
315 |
5 |
| 110 |
55 |
400 |
2 |
CM Casing Pipes - Table - In All Dimensions & MM
General Dimensions
|
Min |
Max |
Min |
Max |
| 40 |
47.9 |
48.2 |
3.5 |
4.0 |
| 50 |
60.0 |
60.2 |
4.0 |
4.6 |
| 80 |
87.9 |
88.3 |
4.0 |
4.6 |
| 100 |
113.0 |
113.3 |
5.0 |
5.7 |
| 125 |
140.0 |
140.4 |
6.5 |
7.3 |
| 150 |
165.0 |
165.4 |
7.5 |
8.5 |
| 175 |
200.0 |
200.5 |
8.8 |
9.8 |
| 200 |
225.0 |
225.5 |
10.0 |
11.2 |
| 250 |
280.0 |
280.5 |
12.5 |
14.0 |
|
