| HYDRAULIC WAGON DRILL KWD – 100
The Best Performer
- Rigid
- Energy Efficient
- Easy Manoeuverability
- Operator Friendly
- High Productivity
- Low Maintenance Cost
- Durability
- Prompt Service Support
Technical Specifications Down the hole air Hammer Capacity:102 to 114 mm. Dia Depth 46 (mtrs)
Mast Length |
3 Meter Drill |
Size of drill Rod |
76 mm. dia |
Rotation Unit Traverse |
3000 mm |
Height Mast raised |
4.7 mtrs. |
Height. Mast lowered |
1.6 mtrs. |
Length. Mast lowered |
5.63 mtrs. |
Length. Mast raised |
4.44 mtrs. |
Mast lateral swivel |
2.0 mtrs. |
Width |
2.07 mtrs. |
Min. / Max. Height for Horizontal drilling
from Ground level |
1.1 mts./2.0 mtrs. |
Compressed Air Requirement |
10.5 cm³ |
Weight of Wagon Drill Rig (Approx) |
2.45 Tons |
Min. Turning radius |
5 mts |
Special Features – Wagon Drill
- Stable drilling capabilities
- Structural designed for extra rigidity
- Base frame in Box-construction Anchoring
arrangement ensures
- perfect stability during drilling
- Rear wheel swivel able by 90º to prevent movement
during toe hole drilling
- Effectively braked wheels with Hydraulic
stabilizer in the front, > holding the unit firmly
- Locking arrangement between mast and boon provides
extra rigidity
- Easy maneuverability-both in manual and self
propulsion modes
- Centralized sensitive controls with Auto feed
arrangement ensure easy operation and reduction of
operators fatigue.
Special Features – Motor Units
- Rotation and winch units provide additional power
for faster drilling and rapid withdrawals, longer tool
life etc., resulting into better productivity
- Heavy duty steel castings & forgings
- Precision machined components
- Durable alloy bearings supported by sturdy
retaining rings
- Heavy duty rotation gear Box with involutes
profile Gear tooth, duly corrected to prevent failure
- Rigid out-put shaft with extra bearing support and
thicker thread profile
- Specially designed Fluid seal to prevent Air
leakage
| Hydraulic System |
B.H.P At 1350 RPM |
Gear Ratio |
Rotation Speed RPM |
Max. Torque |
Pull Down Force |
Pull up Force |
Max. Pull Up Speed |
Travelling Speed |
| Rotation Head |
8.0 - 8.5 |
|
0 - 70 |
97 Kg- mtrs |
-- |
-- |
-- |
-- |
| Feed System (with winch) Feed System (with Ø 80 BoreCyl) |
8.0 - 8.5
19 - 20 |
|
-- |
|
1500 Kgf 3200 Kgf |
1500 Kgf 1600 Kgf |
15 M /Min
27 M /Min |
-- |
| Self Propulsion Unit |
8.0 - 8.5 |
1:98.3 |
-- |
-- |
-- |
-- |
-- |
2 Km/Hr. |
GETECH Products can be supplied in
custom – built models in various configurations,
Mounting features to suit all special requirements and
Technical specifications can be offered accordingly.
(In view of
continuous R&D and Product Improvement programmer
all specifications, features etc., are subject to
amendments without prior notice)
CRAWLER MOUNTED BLAST HOLE DRILL RIG
Technical Specifications ofF Getech-CUBES JV 150 mm BLAST HOLE DRILL – ITD 46
| Description |
Units |
|
US |
Metric |
| General |
|
|
|
|
| Max. Hole Size |
6 |
inch |
152.4 |
mm |
| Max. Hole Depth |
300 |
ft. |
91.4 |
mtrs. |
| Mast Dump Angel (Total |
100 |
Degrees |
100 |
Degrees |
| Mast Swing (on both sides) |
0 to 40 |
Degrees |
0 to 40 |
Degrees |
| Boom Swing (on both Sides) |
0 to 40 |
Degrees |
0 to 40 |
Degrees |
| Max. Hole Spacing |
16.47 |
ft. |
5.02 |
mtrs. |
| (Without Boom Extn.) |
|
|
|
|
| ROTAKRY HEAD TRAVEL |
|
|
|
|
| Speed |
0-60 |
rpm |
0-60 |
rpm |
| Max. Torque |
18000 |
inch-lbs |
207 |
Kgf-m |
| Rotary Head Travel |
13.12 |
ft |
4 |
mtrs |
| Type of Drive |
Hydro - Motor |
Hydro - Motor |
| FEED SYSTEM |
|
|
|
|
| Pull up Speed |
120 |
fpm |
36.6 |
mpm |
| Pull Down Speed |
235.3 |
fpm |
71.74 |
mpm |
| Pull up Force |
11050 |
lbf |
5014.45 |
Kgf |
| Pull Down Force |
5636.45 |
lbf |
2557.4 |
Kgf |
| Type of System |
Powered by Hydraulic cylinder & Rope drive |
| UNDER CARRIAGE SYSTEM |
|
|
|
|
| Max Speed of Equipment |
1.38 |
mph |
2.2 |
Kmph |
| Gradability |
+/- |
30 Degree from Horizontal |
|
| GVW of the Equipment |
17632 |
lb |
8000 |
Kg |
| Grouser Type |
Triple |
Triple |
| Track Width |
77 |
inch |
1955.8 |
mm |
| Wheel Base |
79.13 |
inch |
2010 |
mm |
| Grouser Width |
10 |
inch |
254 |
mm |
| Ground Pressure |
11.14 |
psi |
0.78 |
Kgf/Sq.Cm |
| Tractive Effort |
16201.54 |
lbf |
7351 |
Kgf |
| Track Oscillation |
20 Deg. (10 Deg. On both sides) |
| Type of Drive |
Independent Hydraulic Motor for Each Track |
| Drive System |
Through Planetary Gear Box with In-built Braking |
|
Torque of 50 Kgm (Static) & 25 Kgm (Dynamic) |
| No. of Tollers |
6 on Each Track |
| HYDRAULIC SYSTEM |
|
|
|
|
| Open Loop System Pumps with Pressure Compensated Proportional Values |
|
| Pump – 1 flow |
20 |
gpm |
77lpm |
@ 1800 rpm |
| Pump – 2 flow |
10 |
gpm |
38lpm |
@ 1800 rpm |
| Max. Pressure |
2610.7 |
psi |
180 |
bar |
| Filtration – Return Line |
10 |
microns |
10 |
microns |
| Filtration – Suction Line |
140 |
Microns |
140 |
microns |
| Tank Capacity |
52.8 |
Gallons |
200 |
liters |
| Cooler |
Air to Oil |
|
|
GETECH can supply Products in custom – built models in various configurations, Mounting features to suit all special requirements and Technical
specifications can be offered accordingly.
(In view of
continuous R&D and Product Improvement programme all
specifications, features etc., are subject to amendments
without prior notice.
ITD - 10
Name: ITD 10
Mounting Type:
Crawler mounted
Type of Drilling: Blast Hole
Purpose
Applications: Mines, Quarries
DTH Drilling Capacity:
Max Dia:
6”
Max Depth: 150 feet
Advantages:
- Easy movability with Crawler in uneven Terrains
- Mast Tilting oscillation and swing operation
- Provision for angle Drilling
Rig Specifications
Mast: 4400 mm Pull Up Force: 2200
Kg-f Deck engine: 36HP @ 1500 rpm Suitable Compressor:
540 Cfm @ 185 psi. - IR make
Dimensions: Length: 6800 mm Width:
2200 mm Height: 2000 mm Weight: 4.5 Tons Appx.
Performance
Angle
Drilling: Up to 30º Max. Drilling rateL 60 to 75 feet
per hour Fuel Consumption: 4 to 6 liters per hour Max
Speed: 2 kmph Max. Torque: 120 kgm Max. Rpm: 0 - 8- rpm |
